Sat. Jun 22nd, 2024
How to Replace an iPhone Battery like a Pro

If you’re an iPhone owner, there’s a good chance you’ve experienced some battery drain. Maybe it was a little faster than usual or nearly dead by lunchtime. Whatever the case, if your iPhone battery is draining too quickly and you don’t want to spend money on a new phone, iPhone Battery Replacement yourself is one option that might save you some money.

Replacing your iPhone’s battery can be a relatively straightforward process, but there are some things you should know before attempting it. Below, we’ll take you through replacing an iPhone battery and explain what tools you need and why.

The first thing you need to know about replacing your iPhone’s battery is that it can be tricky. The iPhone contains a small amount of liquid inside its case, called “potting” or “encapsulation,” that helps protect the delicate circuitry from shock and water damage. When you remove the battery from the phone, this liquid will leak out, so make sure to use tools that won’t get damaged before starting the project.

Gather the tools you need :

You will have to connect with a cell phone accessories store for buying a small screwdriver and a flathead screwdriver. You should also have latex or nitrile gloves and a small bowl of warm water to rinse your tools after removing the screws.

If you need the right screwdriver, you can buy one at any hardware store or a big box retailer like Home Depot or Lowe’s.

You’ll also need an anti-static wrist strap to protect your computer from static electricity damage while opening it up. If possible, make sure that the computer is plugged into AC power before beginning disassembly.

Remove the SIM card: If you have a SIM-free phone, skip this step. The iPhone’s SIM card is under a small door on the phone’s right side. Use your flathead screwdriver to pry open the door and remove it.You may need to use a plastic opening tool to help remove the SIM card from its holder.

Remove the battery: The iPhone 5S has a small, rectangular-shaped hole on the bottom of the phone that houses the battery. Use your flathead screwdriver to pry up on this piece of plastic, and then lift out your old battery.

Back up your iPhone

Before you go any further, it’s essential to back up your iPhone. Suppose anything happens during the process, such as a power outage or accidental disconnection of the computer from internet. In that case, it could corrupt the data on your phone and cause problems when you try to restore it.

To back up your phone, connect it to your computer and open iTunes. Select the device icon at the top left of the screen, then click “Back Up Now” in the summary pane on the right side.

Remove the display assembly

The display assembly includes the LCD, digitizer, and home button. If your iPhone 6s has a cracked or broken display, replacing the entire assembly may be easier than just replacing a single component.

If you’re replacing the display assembly, remove it from your iPhone. First, remove the two screws that secure it to the front housing of your phone. These are located at the bottom-center and top-center of the screen. Next, gently lift a suction cup tool (or another pry tool) on one side of the display assembly. The screen will lift slightly, and you can use your fingers to pull it off the housing.

Power down and detach the battery

You’ll want to power down your device and get iPhone Battery Replacement before you start. Hold the power button on your phone for about 10 seconds until you see a “slide to power off” message. Then, press and hold the side button until “Slide to Power Off” appears again.

Press the volume down button to select “Power Off” and press the side button again. When your phone turns off, detach the battery by gently pulling it away from its connector at the bottom of your device.

Reattach the new battery :

Once you have the new battery, reattach it to the device by lining up its connectors with those on your phone. Use your finger or a non-metal tool like a toothpick to push down on each side of the connector, so it clicks into place.

When your battery is securely connected, turn on your phone by pressing the power button. You’ll see a message that says, “Slide to Power Off”—press and hold that message until it dismisses itself.

Your phone will then restart itself; this might take a few minutes. Once it’s back up, check that everything works as expected—you should see any apps you were using before restarting appear in their usual places on the screen.

Reassemble the phone and test it out: If you can turn off and reassemble the phone but don’t see your home screen when you turn it back on, the battery might be faulty. Once you’ve replaced the battery, repeat these steps to ensure you did everything correctly. If that doesn’t work, contact Apple Support for help.

If your iPhone won’t turn on or its screen is entirely black, your battery may run out of power. Plug your iPhone into a power source using its charging cable and wait five minutes before trying again. If this doesn’t work, try resetting your iPhone by holding the Sleep/Wake button

and the Home button together for at least ten seconds until the Apple logo appears. If this still needs to be fixed, contact Apple Support.

Conclusion

If you have one of the iPhone models listed above, iPhone Battery Replacement is something the average person can do themselves. Just be aware that some minor issues could arise; this isn’t one of those tasks that’s totally foolproof. But provided you follow all the steps correctly, a DIY iPhone battery replacement job should be successful for most people. You can follow these steps to get bet results for your iphone.